The World's #1 Renewable Energy Network for News, Information, and Companies.

Economics of Taller Wind Towers

The wind power industry is growing with the trend towards taller towers and larger turbine capacity. Over the past 20 years, the wind energy turbine tower has grown from 40 meters to 90 meters with turbine sizes reaching 2.5 MW. As we progress into the 21st century, the 4.0-MW and 8.0-MW turbine is on the horizon along with towers exceeding 100 meters in height.

Wind energy capacity curves improve with height because the wind profile is stronger. This article analyzes the economics of taller towers and provides a parametric study of tower height vs. power curve. How does the additional cost of taller towers improve the power curve? Is it economical to keep adding height and turbine size? The financial metrics are discussed and a value engineering analysis is presented with conclusions and recommendations for future wind tower design.

The wind energy industry has a short history in our industrial market that starts in the late 1960s. Nevertheless, wind power has existed for over 500 years and evidence exists of wind power utilized by Europeans and Babylonians for their food production process. Our focus, however, is on the immediate present.

Wind energy started with 40m to 50m towers that supported 400-kW to 660-kW turbines. These structures were mostly a truss tower type and still can be seen in certain "wind farm cradles of civilization" such as Palm Springs, Calif. Many of these original designs are still in production, although they require frequent maintenance and the turbines are outdated. These behemoths stand as the cornerstone of the modern wind energy industry. Definitely not attractive designs, they symbolize the start of this growth curve in our demand for clean energy. [Editor's note:  The chart below is a two-page spread in the print edition.  Imagine the bottom half of the chart attached to the right of the top half.  We apologize for the small print.]

chart continues as if across the page.

From the late 1970s to the 1990s, the industry remained below the 50m tower height limitation because the wind energy industry went through several cycles of growth and collapse. As we progress to the late 1990s, turbine technology shifted to 800-kW to 1.0-MW machines and tower hub heights reached 60m and 70m. Turbine technology demanded larger rotor diameters and thus taller towers. It finally became apparent that it was cheaper to construct fewer wind towers with larger capacity because this would reduce the total infrastructure cost.

To move forward with 1.0-MW and 1.5-MW machines, the towers became tubular steel structures and foundation design solutions were needed to solve the ever-growing load demand on the structure. These tubular steel structures have become the mainstay of the wind tower market.

After 2000, the turbine market has heated up and reached new levels of capacity. We are now in the age of renewable energy with increasing demand for this product. New tower technology is necessary to keep up with the industry.

Turbine Sizes and Clean Energy Demand

The past 10 years have seen a flurry of growth for new turbine technology due to the pent-up demand globally for green energy sources. The worldwide market for renewable energy is growing and has a positive outlook for the next 10 years. Turbine sizes are averaging 2.0-MW to 3.0-MW for onshore projects, with new turbines developed at the 4.0- and 5.0-MW sizes. These all require towers of 80m minimum hub heights. For the onshore market, the 3.0 MW turbines are fast becoming the standard, with 90m tower heights.

For offshore wind, which is still in its infancy globally, the minimum turbine sizes are 5.0-MW and growing to 7.0-MW. In this author's opinion, the offshore market will continue to grow because ultimately that is where the highest efficiency curves are obtained. High capacity factors translate into stronger financial performance, which further excites the investment community and stimulates more capital inflow.

The American Wind Energy Association (AWEA) website states that 8,500 MW of wind power generation was added in 2009. This is equivalent to 8.5 GW or approximately nine medium-sized nuclear power plants. The industry is poised for growth.

New Turbine Technology and Cost Factors

New turbines are being developed for 7.0-MW and 10.0-MW capacities that require 100m rotor diameters and minimum 100m tower heights. Larger turbines allow fewer towers to do the work of many smaller turbines. A simple arithmetic exercise shows the economic advantages:

Example of 100-MW onshore wind farm:

    25 towers @ 4 MW
    25 towers @ $500k/tower = $12.5 million in structure + foundation
    10 miles roads @ $1.5 million/mile = $15 million
    Total infrastructure cost = $27.5 million or $275,000/MW
    100 towers @ 1 MW
    100 towers @ $350k/tower = $35 million in structure + foundation
    50 miles of roads @ $1.5 million/mile = $75 million of road
    Total infrastructure cost = $110 million = $1,100,000/MW

By increasing the tower size and turbine capacity, we can reduce the infrastructure cost tremendously. There are numerous additional advantages to having fewer towers per project:

  • Less environmental impact overall; fewer roads, which means a smaller area of the site is impacted with construction traffic
  • Less earthwork and grading impact
  • Taller towers with larger turbines results in low frequency rotation of the rotor (<15 rpm), which means less bird impact issues (birds can detect the lower rotation blades and divert their flight path)
  • Fewer turbines means overall lower maintenance cost because there are less machines to monitor; it's easier to monitor 25 towers versus 100.

Taller towers that are becoming the mainstream and reaching heights above 100m fuel demand for creative engineering solutions. Several firms are pursuing innovative tower designs. The main ideas focus on using the basic tubular steel tower concept, but numerous alternative design concepts use composite towers with steel and concrete. Technical challenges are posed in tall towers and the structural engineering aspects become complicated.

Here are 12 issues that confront structural engineers in tower design:

Turbine over-speed: The turbine and rotor run into over speed (>24 rpm) at wind speeds over 50 mph. This results in excessive loads and the entire system can collapse.


E-stop: The short/hard stop creates a shock load spectrum on the structure and results in a drastic dynamic impulse load to the system, resulting in large lateral deflections.


Frequency-rotational stiffness: Long-term soil fatigue and/or foundation fatigue cause the tower-structural system to degrade and the rotational stiffness reduces over time. This causes the structural period to lengthen (frequency shortens) leading eventually to a resonance problem.


Fatigue failure of welds: Steel welds that crack over long-term fatigue due to built up residual stresses. The buckling capacity of the tower is reduced and eventually the tower shell collapses.


Blade failure: Blades are overstressed due to fatigue, wear and tear, excessive vibration and collapse from these external loads.


Turbine eccentricity loads: The turbine design and yaw plates are not designed properly and have built-in eccentricities that were not accounted for in the original load calculations. These eccentricities lead to long term fatigue cracking in the yaw plate.


Rotor imbalance: The rotor and blades have built-in imbalance and eccentric moments are created in the blade rotation. Imbalance due to snow/ice loads will also cause unusual load spectrums that were not part of the original design spectrum.


Residual stresses induced by internal welds: Internal welds were done on the tower without manufacturer approval and cause built-up stresses. These residual stresses lead to premature fatigue cracking.


Foundation cracking from fatigue: The base foundation cracks due to fatigue cyclic loads and result in a reduction of the foundation rotation stiffness. This affects the tower performance and may lead to resonance induced amplitude magnification of the tower structure.


Foundation softening due to poor drainage: The base foundation structure-soil interface softens due to concentrated drainage problems. This may lead to weakened soil parameters (due to the presence of water) and degrading lateral stiffness.


Corrosion of foundation bolts from aggressive soils: The soil has aggressive properties that lead to deterioration of the concrete and penetration into the bolts/reinforcement. Corrosion of bolts/reinforcement leads to reduced foundation structural capacity and eventual stiffness degradation.


Seismic/earthquake loads: Tower designers consider wind loads without evaluating the earthquake/seismic effects and the towers may not be capable of resisting the local seismic demands.

The most unique aspect of wind tower structural design is the dynamic characteristics and fatigue-elated issues. Of all civil engineered structures, the wind tower stands as an inherently special structure because it is a "working machine" with moving parts, versus a bridge or high rise building. These inherent dynamic loads create many issues that are not normally considered in static structures.

Long-term loads are the normal operational wind loads that include dead, live, static wind pressure and standard operational overturning moments, shears and axial loads. The frequency of these long-term sustained loads may reach over 20,000,000 cycles in 20 years. Therefore, every aspect of the tower-foundation design must consider these provisions. Short-term loads include E-stop, earthquake, peak wind dynamic pressure and three-second gust load.

For offshore projects, the issues are further compounded with additional technical complexities:

  • Hydrodynamic wave loading on the tower foundation
  • Frequency response of tower-foundation with complexity of the wind and water wave action on the structure
  • Fatigue and corrosion from the water-wave action
  • Submarine access to the foundation for monitoring and maintenance
  • Geotechnical performance of the sub-sea floor foundation behavior.

Furthering this discussion for taller towers are the foundation elements that must complement the larger structure and increased loads.

Wind towers continue to grow in height and load capacity. We are now looking at the next generation of wind towers which will exceed 100m in height and carry 7.0 MW and larger-sized turbines. In this author's estimation, we will see the average tower height be 120m by 2015 with 7.0 MW turbines as the typical case.

As we move forward, we can improve our design practice by developing an inventory of towers and asking difficult questions. Areas for further research include:

Structural Performance Monitoring: Monitor a select sample size of towers to keep a track record of their loads, stresses and performance.

Comprehensive Research on Structural Failures: A research report should be commissioned to examine the inventory of tower designs and documented failures. Little information exists on this topic in the research community and we need more information.

Evaluation of All Load Conditions: There is a lack of information on the scope of design loads and what they should include. Perhaps a revised standard is warranted to form uniform platform for all manufacturers.

Sharing our Design Problems for Discussion: Our technical teams should communicate and share their successes and problems. The best way to improve is to discuss these in an open forum.

Statistical Record Keeping: As an industry, we should be keeping records of problems and issues so that we can track the performance of various systems.

Improving the Design Codes: All of these efforts should be consolidated into a wind tower structural design committee that can recommend improvements to our design codes.


Dr. Dilip Khatri is Principal Structural Engineer with the URS Corp. in Los Angeles and has 27 years of experience in all areas of civil engineering. He has worked in the wind energy industry for 10 years designing towers, foundations and civil projects. His experience in the seismic and earthquake engineering industry includes conducting numerous insurance investigations into commercial loss along with investigating failures for commercial line carriers. Dr. Khatri has extensive experience with tall structures, dynamic analysis, earthquake response and construction of complex structural systems and infrastructure design. He has published over 30 technical papers, two textbooks and conducted over 100 symposiums and conferences internationally.

RELATED ARTICLES

Slow down sign

Reality Check: Maybe Energy Storage Isn't Ready for Prime Time

Meg Cichon, Associate Editor Highlighting the growth of the energy storage market at the at the 2015 Energy Storage Association Conference in Dallas, Texas, Oncor’s  VP of Transmission Operations Wes Speed compared the industry to the Texas rain: ...
Renewable energy investment

Smart Investments: Ditch Your CD for Renewable Energy Yieldco Dividends

Susan Kraemer, Correspondent Renewable energy yieldcos have gain traction in the past few years, and are certainly making it easier to develop projects. But many don’t realize that yieldcos also offer solid financial benefits for the average person who...
Risk and reward

Managing the Risks of Renewable Energy Projects in Developing Countries

Jeffrey Karp, Jim Wrathall and Morgan Gerard, Sullivan & Worcester Driven by rapid expansion in developing countries, renewables are becoming a significant source of the world’s power.  According to the United Nations Environmental Programme’s (UNEP) 9th “Global Trends in Renewable En...
Ukraine flag

US Companies Invest Millions in Ukraine Bioenergy Despite Turbulent Policy

Vladislav Vorotnikov, International Correspondent Massachusetts-based Briggs Capital plans to invest US$250 million in the Ukraine bioenergy sector within the next several years, according to its CEO Rhode Robertson. The announcement was made amid significant problems in U...

CURRENT MAGAZINE ISSUE

Volume 18, Issue 3
1505REW_C11

STAY CONNECTED

To register for our free
e-Newsletters, subscribe today:

SOCIAL ACTIVITY

Tweet the Editors! @megcichon @jennrunyon

FEATURED PARTNERS



EVENTS

Doing Business in Brazil – in partnership with GWEC, the Global Win...

Brazil is one of the most promising markets for wind energy.  Ranke...

Mastering RETScreen® 4 for Clean Energy Project Analysis

Hands-on modeling class using RETScreen 4. Michael Ross designed this co...

RECAM WEEK

RECAM WEEK will bring together the incredibly successful SPG Central Am...

COMPANY BLOGS

SunEdison Expands Residential Market Offerings with New PPA, Sales ...

SunEdison has largely focussed on the commercial and utility-scale solar...

Are You Ready for a Natural Disaster?

Guest post by Jenna Clarke  Living in the Shenandoah Valley of Virg...

Deadline for Inclusion in Solar Power World's Top Solar Contractors...

UPDATE: The official deadline for the Solar Power World T...

NEWSLETTERS

Renewable Energy: Subscribe Now

Solar Energy: Subscribe Now

Wind Energy: Subscribe Now

Geothermal Energy: Subscribe Now

Bioenergy: Subscribe Now  

 

FEATURED PARTNERS